Muffle Furnace Exhaust Muffler Kit

Muffle Furnace Exhaust Muffler Kit

Introduction to Furnace Muffler

It pulls oxygen into the kiln for better colors, especially for red and orange glazes and decals. Fire red and green glazes in the same load without glaze contamination. The Exhaust Kit pulls air from the furnace, dilutes it with room air and pushes it out the other side. There should be no worries about compatibility with various heating or air valves, ensuring easy installation and operation.

The extra oxygen and air movement burns carbon out of the clay, which eliminates a host of firing problems: bloating, dark spots in the clay, porcelain mildew, pinholes, pitting, blisters and bubbles.

The Exhaust Kit removes fumes with volatile metals, fluorides and sulphur oxides. You can fire lusters, decals, metallics and pate-de-verre glass without strong odor.

The flow of fresh air evens out the temperature in the furnace. The vent extends the life of the Muffle Furnace tube assembly since fumes bypass the tube. You will enjoy the convenience of the Economy Muffle Furnace Exhaust Kit. Throughout the firing keep the lid closed and peephole plugs in. No more remembering to lower the hot lid from vented position.

The Economy Muffle Furnace Exhaust Kit adds 5 minutes to firings up to cone 4, 12 minutes to firings from cone 4 to 10. It has little effect on top temp. At 132 watts the Exhaust Kit motor uses only pennies per firing. You can measure the effectiveness of the kit by measuring noise levels and system efficiency before and after installation.

From shut off to 1000°F the Economy Muffle Furnace Exhaust Kit has little effect on cool down time. From 1000°F to room temp it reduces cool down time by 2 hours.

The Economy Muffle Furnace Exhaust Kit requires a separate 120 volt wall plug unless your furnace is equipped with the AOP vent.

A 3’ long 2” duct comes with each vent. The 2” duct runs between the collection cup and the blower motor. Use 4” aluminum dryer duct or 4” PVC pipe between the motor and the vent outlet. (Do not use vinyl dryer duct.)

Position the Economy Muffle Furnace Exhaust Kit next to the furnace and attach the collection cup to the bottom or side of the furnace. The collection cup fits under most top-loading kilns. Since the vent motor is away from the furnace there is no vibration in the furnace or gases, the motor is away from the heat of the furnace and the fan is easy to clean. The Economy Muffle Furnace Exhaust Kit works with all Economy Muffle Furnaces except the smallest tabletop models.

Product Description

The Carrier muffler is a high quality in-line muffler designed to reduce noise levels and gases in buildings. This single piece unit is easy to install and replace existing mufflers. It fits into ducts without modification, a practical solution for people in noisy buildings. Whether you need to replace an old muffler or install a new one the Carrier muffler is a seamless and efficient solution.

Key Features and Benefits

• Reduces Noise Levels: The Carrier muffler is designed to minimize noise.

• Modular Design: Easy to install.

• Compatibility: Works with various furnace models including Lennox.

• Easy Fit: Fits into existing ducts without modification.

• Practical Solution: For people in noisy buildings, noticeable reduction in noise and gases

Technical Specifications

• Material: High quality durable materials.

• Dimensions: Designed to fit existing equipment and ducts.

• Compatibility: Works with Lennox furnace models.

• Installation: Easy to install and replace existing mufflers, minimal disruption.

• Insulation: Requires heat tape or insulation in cold temperatures to function properly.

Installation and Compatibility

The Carrier muffler is a drop-in replacement for existing mufflers, easy installation. It works with various furnace models including Lennox and up to 125’ vent lengths. However do not install in areas where temperatures will be below freezing without additional protection such as heat tape or insulation to function properly.