Durham Geo TR-27303 SRX 6in Well Seal Assembly

TR-27303 6-inch Well Seal Assembly for SRX Pumps | DGSI Slope Indicator Submersible Pumps

DGSI well seals provide an easy method for connecting fluid and air lines to simplify installations.

• Strain relief seals isolate the individual DGSI tubing sizes used on the SRX pumps and are vacuum rated.
• The well seals are attached to the casing, sealing them to the diameter of the well casing with a Fernco™-type flexible coupling.
• Additional threaded openings through the seals are provided for fluid level monitoring.
• Eyehook included for attaching pump support cable.

Well Seals Construction

• Fernco-type seal: Neoprene rubber, stainless steel hose clamps
• Eyelet for pump construction: Type 304 stainless steel
• Compression seals for hoses and tubing: Nylon® and neoprene rubber
• Pipe plugs: Nylon®
• Hardware misc.: 18-8 stainless steel
• Top seal plate: Gray PVC

SRX Pumps

• The SRX is an air-powered pump used to extract ground water or total fluids at variable rates equal to the well recharge rates.
• The SRX is available in a 1.75in OD or 3.5in OD for use in 2” and 4” wells.
• Pump flow rates are up to 9.5 gpm.
• The SRX pump is available in top loading for recovering total fluids or bottom loading for dissolved phase and higher pumping rates.
• Top-loading pumps (SRX-R TL) are selected for pumping total fluids (LNAPL and ground water simultaneously). Water table drawdown will be maintained at a level corresponding to the top inlet of the pump. Pumps of shorter lengths are available for lower drawdown requirements
• Bottom-loading pumps (SRX-R BL) are selected for dissolved phase or DNAPL applications. When installing the pump, the head is positioned at a depth of approximately 10 inches higher than the desired water table depression.

Better Value

• More Uptime:
  • Reliable
  • Simple Routine Maintenance
• Competitive Price
• Easy Replacement for Existing Pump
• Fewer Parts

Advantages

• Advanced, positive-sealing air valves with built-in filtration.
• Complete field disassembly with only one wrench.
• Constructed with durable materials such as stainless steel, brass, Buna-N®, Nylon® and Viton®.
• Durable Ebonite float.
• Light weight.

Applications

Applications for SRX Remediation Pumps include

• Pneumatic pumps for use in 2-inch and larger-diameter wells up to 200 ft.
• Pneumatic pump for extracting groundwater or total fluids in both top-loading or bottom-loading environments.

Pump Specifications

Construction 

• Stainless steel, Type 304: Pump body, discharge tube
• Stainless steel, Type 303: Pump head, bottom intake valve,
• assembly control rod, control linkage assembly
• Brass: Hose and tubing barbs
• Hydlar (Nylon/Kevlar® composite): Control rod bushing
• Nylon®: Discharge and top-loading check valve ball
• Buna-N®: Botton intake check valve ball
• Viton®: O-ring seals, air inlet ball valve
• Ebonite (expanded Buna-N®): Float
• Neodymium Iron: Magnets
• Red brass: Top intake casting

Selection Table For SRX Remediation Pumps

Part Number & Model¹ | Nominal Size | Pump OD | Pump Length | Volume per Cycle² | Min. Submergence (in) | Pump Weight (lb) | Max. Flow Rate³ (gpm) | Air Valve Filtration

• TR-974 SRX-R TS (short) 4.0” | 3.5” | 39.0” | 0.2gal | 39.0” | 16.6lb | 5.5gpm | Yes
• TR-975 SRX-R BL 4.0” | 3.5” | 46.2” | 0.4gal | 29.1” | 16.7lb | 9.5gpm | Yes
• TR-976 SRX-R TL 4.0” | 3.5” | 44.5” | 0.4gal | 44.5” | 18.0lb | 7.6gpm | Yes
• TR-977 SRX-R BL 2.0” | 1.75” | 44.0” | 0.12gal | 29.3” | 4.0lb | 2.9gpm | Yes*
• TR-978 SRX-R TL 2.0” | 1.75” | 43.5” | 0.12gal | 43.5” | 4.2lb | 1.8gpm | Yes*

1 SRX-R TS = top-loading, short, SRX-R BL = bottom-loading, SRX-R TL = top-loading.
2 Volume (US gal) per pump cycle will vary slightly depending on air pressure supplied to pump, depth of well, etc.
3 Maximum flow rates can vary due to air pressure supplied to pump, depth of well, etc. For assistance, contact DGSI.
* SRX-R inlet filter only.

Downloads

• SRX-II brochure (PDF)